1-20 of 26
Keywords: stainless steel
Close
Sort by
Journal Articles
Journal Articles
Journal Articles
Publisher: ASME
Article Type: Research Papers
J. Eng. Mater. Technol. July 2011, 133(3): 031003.
Published Online: June 24, 2011
...S. Nakhodchi; B. G. Thomas; D. J. Smith Residual stresses in a stainless steel vessel containing glass have been evaluated using measurements and numerical simulation. High-level nuclear wastes are often vitrified in glass cast in cylindrical stainless steel containers. Knowledge of the internal...
Journal Articles
Journal Articles
Publisher: ASME
Article Type: Research Papers
J. Eng. Mater. Technol. April 2011, 133(2): 021012.
Published Online: March 21, 2011
...M. E. Kassner; P. Geantil; R. S. Rosen This study reports the significant ambient temperature creep plasticity at stresses below the conventional 0.2% plastic strain off-set yield stress. This is partially due to the relatively high strain-rate sensitivity of 304 stainless steel. Cold-working...
Journal Articles
Journal Articles
Publisher: ASME
Article Type: Research Papers
J. Eng. Mater. Technol. October 2010, 132(4): 041004.
Published Online: September 10, 2010
...Alberto Polar; J. E. Indacochea; M. L. Wang The creep evolution was followed by conducting magnetic measurements on ferromagnetic steel samples exposed to different creep strains at a constant temperature. 410 stainless steel (410 SS) rods were submitted to creep at 625 ° C applying a constant...
Journal Articles
Publisher: ASME
Article Type: Research Papers
J. Eng. Mater. Technol. July 2010, 132(3): 031015.
Published Online: June 24, 2010
... ranging from 1 μ m to 10 μ m on stainless steel, titanium, and aluminum. The results indicate that the geometrical characteristics of the interference patterns as well as the thermal properties of the substrates determine the quality of the fabricated structures. In particular, the best structures were...
Journal Articles
Journal Articles
Journal Articles
Journal Articles
Publisher: ASME
Article Type: Research Papers
J. Eng. Mater. Technol. July 2009, 131(3): 031002.
Published Online: May 21, 2009
... and then fabricated, modeled, and experimentally validated. To provide a unique biaxial stress state, a 60 mm diameter 10 mm thick disk of 316L stainless steel was plastically compressed through the thickness with an opposing 15 mm diameter hard steel indenters in the center of the disk. For validation, the stresses...
Journal Articles
Publisher: ASME
Article Type: Research Papers
J. Eng. Mater. Technol. July 2008, 130(3): 031013.
Published Online: June 11, 2008
.... The point of the slope change is defined as the fatigue life of the specimen. The cyclic softening behavior of AL6XN distinguishes this alloy from the 300-series stainless steels. In the case of the metastable steels (for instance, 304 or 316), cyclic softening is followed by cyclic hardening, which...
Journal Articles
Journal Articles
Journal Articles
Publisher: ASME
Article Type: Technical Papers
J. Eng. Mater. Technol. October 2007, 129(4): 567–579.
Published Online: May 23, 2007
... conditions. These materials were AISI H13 tool steel, AISI 316L stainless steel, AISI 52100 hardened steel, and AISI 4340 steel. The Johnson–Cook (J–C) constitutive equation was used to model the plastic behavior of the workpiece material. Different values were assigned to the J-C parameters representing...
Journal Articles
Publisher: ASME
Article Type: Technical Papers
J. Eng. Mater. Technol. July 2007, 129(3): 414–421.
Published Online: December 26, 2006
... the effective stresses and effective strains under a biaxial stress state. Annealed AA6011 aluminum tubes and SUS409 stainless-steel tubes were used for the bulge test. The tube thickness at the pole, bulge height, and the internal forming pressure were measured simultaneously during the bulge test...
Journal Articles
Journal Articles
Publisher: ASME
Article Type: Research Papers
J. Eng. Mater. Technol. January 2005, 127(1): 154–158.
Published Online: February 22, 2005
... 26, 2003; revision received September 9, 2004. Review conducted by: M. F. Horstemeyer. 26 December 2003 09 September 2004 22 02 2005 stainless steel tool steel hardness hardness testing indentation work hardening elastic moduli yield strength tensile testing finite...
Journal Articles