Skip Nav Destination
Issues
November 2000
ISSN 1087-1357
EISSN 1528-8935
In this Issue
Technical Papers
Thermal Aspects of Grinding: The Case of Upgrinding
J. Manuf. Sci. Eng. November 2000, 122(4): 605–611.
doi: https://doi.org/10.1115/1.1285877
Topics:
Grinding
,
Heat
,
Shear (Mechanics)
,
Temperature
,
Wear
,
Fluids
,
Wheels
Finite Element Modeling of Burr Formation Process in Drilling 304 Stainless Steel
J. Manuf. Sci. Eng. November 2000, 122(4): 612–619.
doi: https://doi.org/10.1115/1.1285885
Topics:
Drilling
,
Finite element analysis
,
Simulation
,
Stainless steel
,
Modeling
,
Deformation
,
Geometry
,
Stress
,
Failure
,
Drills (Tools)
Surface Integrity of Die Material in High Speed Hard Machining, Part 1: Micrographical Analysis
T. I. El-Wardany, Research Associate, H. A. Kishawy, Ph.D. Candidate, M. A. Elbestawi, Professor, Fellow ASME
J. Manuf. Sci. Eng. November 2000, 122(4): 620–631.
doi: https://doi.org/10.1115/1.1286367
Topics:
Cutting
,
Machining
,
Tool steel
,
Wear
,
Surface roughness
Surface Integrity of Die Material in High Speed Hard Machining, Part 2: Microhardness Variations and Residual Stresses
T. I. El-Wardany, Research Associate, H. A. Kishawy, Ph.D. Candidate, M. A. Elbestawi, Professor, Fellow ASME
J. Manuf. Sci. Eng. November 2000, 122(4): 632–641.
doi: https://doi.org/10.1115/1.1286557
Topics:
Cutting
,
Machining
,
Residual stresses
,
Stress
,
Microhardness
,
Finite element analysis
,
Wear
,
Tool steel
,
Turning
Effect of Cutting-Edge Geometry and Workpiece Hardness on Surface Residual Stresses in Finish Hard Turning of AISI 52100 Steel
J. Manuf. Sci. Eng. November 2000, 122(4): 642–649.
doi: https://doi.org/10.1115/1.1286369
Mechanics of Machining With Chamfered Tools
J. Manuf. Sci. Eng. November 2000, 122(4): 650–659.
doi: https://doi.org/10.1115/1.1286368
Topics:
Cutting
,
Deformation
,
Flow (Dynamics)
,
Machining
,
Shear (Mechanics)
,
Stress
,
Temperature
,
Steel
An Analytical Representation of Chip Area for Corner-Radiused Tools Under Both Depth-of-Cut and Feed Variations
O. Burak Ozdoganlar, Graduate Student Research Assistant, William J. Endres, Assistant Professor, Mem. ASME
J. Manuf. Sci. Eng. November 2000, 122(4): 660–665.
doi: https://doi.org/10.1115/1.1286470
Topics:
Corners (Structural elements)
,
Error compensation
,
Errors
,
Geometry
,
Cutting
,
Shapes
,
Machining
Experimental Evaluation of the Laser Assisted Machining of Silicon Nitride Ceramics
J. Manuf. Sci. Eng. November 2000, 122(4): 666–670.
doi: https://doi.org/10.1115/1.1286556
Topics:
Cutting
,
Cutting tools
,
Lasers
,
Machining
,
Silicon nitride ceramics
,
Temperature
,
Wear
,
Ceramics
,
Surface quality
,
Grinding
Development of a Cutting Direction and Sensor Orientation Independent Monitoring Technique for End-Milling
J. Manuf. Sci. Eng. November 2000, 122(4): 671–677.
doi: https://doi.org/10.1115/1.1286169
Topics:
Cutting
,
Milling
,
Signals
,
Failure
,
Accelerometers
,
Sensors
,
Eigenvalues
Determination of Heat Transfer Coefficients Using a 1-D Flow Model Applied to Irregular Shaped Cooling Channels in Pressure Diecasting
J. Manuf. Sci. Eng. November 2000, 122(4): 678–690.
doi: https://doi.org/10.1115/1.1285913
Topics:
Boiling
,
Boundary element methods
,
Casting
,
Coolants
,
Cooling
,
Flow (Dynamics)
,
Heat transfer
,
Heat transfer coefficients
,
Pressure
,
Steady state
Non-Destructive Machinability Characterization of Materials Through a Correlation With Rate of Strain Sensitivity
Jeffrey A. Sprague, Research Engineer,, Evangelos C. Eleftheriou, Assistant Professor,, Charles E. Bates, Research Professor,
J. Manuf. Sci. Eng. November 2000, 122(4): 691–697.
doi: https://doi.org/10.1115/1.1285902
Topics:
Machinability
,
Cutting
,
Viscosity
,
Design
,
Stress
Parametric Study of Heat Transfer in Injection Molding—Effect of Thermal Contact Resistance
J. Manuf. Sci. Eng. November 2000, 122(4): 698–705.
doi: https://doi.org/10.1115/1.1287348
Topics:
Cavities
,
Contact resistance
,
Heat transfer
,
Injection molding
,
Pressure
,
Shrinkage (Materials)
,
Simulation
,
Temperature
,
Warping
,
Cooling
A Finite Element Approach to Transient Thermal Analysis of Work Rolls in Rolling Process
James D. Lee, Professor, Majid T. Manzari, Assistant Professor, Yin-Lin Shen, Associate Professor, Wenjun Zeng, Doctoral Student
J. Manuf. Sci. Eng. November 2000, 122(4): 706–716.
doi: https://doi.org/10.1115/1.1287590
An Approach for Modeling Sheet Metal Forming for Process Controller Design
C.-W. Hsu, Graduate Student Research Assistant, A. G. Ulsoy, Professor and Fellow ASME, M. Y. Demeri, Senior Technical Specialist,
J. Manuf. Sci. Eng. November 2000, 122(4): 717–724.
doi: https://doi.org/10.1115/1.1286815
Topics:
Blanks
,
Control equipment
,
Friction
,
Sheet metal work
,
Design
,
Modeling
,
Tooling
A Multi-Sensor Approach for Rapid Digitization and Data Segmentation in Reverse Engineering
V. H. Chan, Assistant Professor, Assoc. Mem. ASME,, C. Bradley, Associate Professor, G. W. Vickers, Professor
J. Manuf. Sci. Eng. November 2000, 122(4): 725–733.
doi: https://doi.org/10.1115/1.1286125
Modeling and Calibration of Grid Structured Light Based 3-D Vision Inspection
J. Manuf. Sci. Eng. November 2000, 122(4): 734–738.
doi: https://doi.org/10.1115/1.1286126
Topics:
Calibration
,
Inspection
,
Modeling
Ingredient-Wise Study of Flux Characteristics in the Ceramic Membrane Filtration of Uncontaminated Synthetic Metalworking Fluids, Part 1: Experimental Investigation of Flux Decline
Steven J. Skerlos, Graduate Research Assistant,, N. Rajagopalan, Senior Research Engineer,, Richard E. DeVor, Professor and Fellow ASME, Shiv G. Kapoor, Professor and Fellow ASME,, V. Don Angspatt, Director of Research and Development,
J. Manuf. Sci. Eng. November 2000, 122(4): 739–745.
doi: https://doi.org/10.1115/1.1286132
Topics:
Filtration
,
Fluids
,
Membranes
,
Ceramics
,
Lubricants
,
Water
,
Metalworking
Ingredient-Wise Study of Flux Characteristics in the Ceramic Membrane Filtration of Uncontaminated Synthetic Metalworking Fluids, Part 2: Analysis of Underlying Mechanisms
Steven J. Skerlos, Graduate Research Assistant,, N. Rajagopalan, Senior Research Engineer,, Richard E. DeVor, Professor and Fellow ASME, Shiv G. Kapoor, Professor and Fellow ASME, V. Don Angspatt, Director of Research and Development,
J. Manuf. Sci. Eng. November 2000, 122(4): 746–752.
doi: https://doi.org/10.1115/1.1286131
Topics:
Fluids
,
Membranes
,
Lubricants
,
Filtration
Performance Analysis of Parallel Mechanism Architectures for CNC Machining Applications
J. Manuf. Sci. Eng. November 2000, 122(4): 753–759.
doi: https://doi.org/10.1115/1.1289290
Intrinsic Errors on Sheet Strain Measurements Based on a Printed Square Grid
J. Manuf. Sci. Eng. November 2000, 122(4): 760–765.
doi: https://doi.org/10.1115/1.1312337
Topics:
Errors
,
Strain measurement
,
Biological tissues
,
Periodic structures
Fixturing of Compliant Parts Using a Matrix of Reconfigurable Pins
J. Manuf. Sci. Eng. November 2000, 122(4): 766–772.
doi: https://doi.org/10.1115/1.1314599
Topics:
Clamps (Tools)
,
Deflection
,
Design
,
Electromagnets
,
Fixturing
,
Machining
,
Pins (Engineering)
,
Springs
,
Stress
,
Computers
Dimensional Fault Diagnosis for Compliant Beam Structure Assemblies
J. Manuf. Sci. Eng. November 2000, 122(4): 773–780.
doi: https://doi.org/10.1115/1.1285917
Topics:
Eigenvalues
,
Fault diagnosis
,
Manufacturing
,
Stiffness
,
Modeling
,
Errors
,
Principal component analysis
A Useful Solution for Estimating Contact Pressure Between a Plate and Foundation
J. Manuf. Sci. Eng. November 2000, 122(4): 781–789.
doi: https://doi.org/10.1115/1.1286167
Topics:
Pressure
,
Stiffness
,
Finite element methods
Machining Cost Optimization Involving Shift and Overtime Work
J. Manuf. Sci. Eng. November 2000, 122(4): 790–794.
doi: https://doi.org/10.1115/1.1314600
Topics:
Cutting
,
Machining
,
Optimization
Technical Brief
Evaluation of Minimum Zone Straightness by a Nonlinear Optimization Method
J. Manuf. Sci. Eng. November 2000, 122(4): 795–797.
doi: https://doi.org/10.1115/1.1285880
Topics:
Algorithms
,
Coordinate measuring machines
,
Filters
,
Optimization
,
Robustness
,
Reliability
,
Fittings
Email alerts
RSS Feeds
On-Orbit Processing and Hardware Performance of Microgravity Hydrothermal Synthesis for Graphene Aerogel
J. Manuf. Sci. Eng (December 2024)
A Review on Metallic Drilling Burrs: Geometry, Formation, and Effect on the Mechanical Strength of Metallic Assemblies
J. Manuf. Sci. Eng (April 2025)
A Generalized Machining Process Damping Model for Orthogonal Cutting
J. Manuf. Sci. Eng