1-20 of 94
Keywords: nozzles
Close
Follow your search
Access your saved searches in your account

Would you like to receive an alert when new items match your search?
Close Modal
Sort by
Journal Articles
Journal Articles
Publisher: ASME
Article Type: Research Papers
J. Eng. Gas Turbines Power. April 2012, 134(4): 041506.
Published Online: February 1, 2012
... chamber was designed and set up. The size and operating conditions were configured to enable flame stabilization by recirculation of hot combustion products. The geometry of the rectangular confinement and an off-center positioning of the jet nozzle were chosen to resemble one burner nozzle of a FLOX ®...
Journal Articles
Publisher: ASME
Article Type: Research Papers
J. Eng. Gas Turbines Power. March 2012, 134(3): 031201.
Published Online: December 28, 2011
... transcendental relations where closed-form solutions may be desirable. 22 02 2011 02 04 2011 28 12 2011 28 12 2011 confined flow equations of state heat transfer iterative methods Mach number nozzles specific heat stagnation flow subsonic flow supersonic flow One...
Journal Articles
Publisher: ASME
Article Type: Research Papers
J. Eng. Gas Turbines Power. February 2012, 134(2): 021501.
Published Online: December 9, 2011
... on mixing characteristics and the resulting temperature distribution and pollutant emissions. As the P/T fuel ratio increases, the high temperature region over 1900 K enhances reaction of the mixture from the main nozzle in the primary mixing zone. For low P/T ratios, the pilot stream dilutes the mixture...
Journal Articles
Publisher: ASME
Article Type: Research Papers
J. Eng. Gas Turbines Power. December 2011, 133(12): 122401.
Published Online: August 31, 2011
...K. K. Botros Nozzle type check valves are often employed in compressor stations in three locations: compressor outlet, station discharge, and station bypass. The fundamental design concept of these valves is based on creating a converging diverging flow through the valve internal geometry...
Journal Articles
Publisher: ASME
Article Type: Research Papers
J. Eng. Gas Turbines Power. November 2011, 133(11): 111502.
Published Online: May 19, 2011
...Greg Pucher; William Allan; Marc LaViolette; Pierre Poitras Differences in exhaust emissions, smoke production, exhaust pattern factor, deposit buildup, and fuel nozzle spray characteristics for various blends of conventional commercial jet fuel (Jet A-1) with synthetic and biodiesel formulations...
Journal Articles
Publisher: ASME
Article Type: Research Papers
J. Eng. Gas Turbines Power. November 2011, 133(11): 112802.
Published Online: May 19, 2011
...Hyun Kyu Suh; Chang Sik Lee This paper presents the effect of orifice configuration on the droplet atomization characteristics of diesel fuel injected through different types of group-hole nozzle angles, which are converged ( θ = − 3 deg ) , parallel ( θ = 0 deg ) , and diverged ( θ = + 3 deg...
Journal Articles
Publisher: ASME
Article Type: Research Papers
J. Eng. Gas Turbines Power. October 2011, 133(10): 101201.
Published Online: May 3, 2011
...David Munday; Nick Heeb; Ephraim Gutmark; Junhui Liu; K. Kailasanath This paper presents observations and simulations of the impact of several technologies on modifying the flow-field and acoustic emissions from supersonic jets from nozzles typical of those used on military aircraft. The flow-field...
Journal Articles
Publisher: ASME
Article Type: Research Papers
J. Eng. Gas Turbines Power. September 2011, 133(9): 092001.
Published Online: April 20, 2011
.... This paper addresses the influence and importance of droplet size on evaporative cooling performance and efficiency. Spray nozzles used for inlet fogging and wet compression include impaction pin, swirl jet, air assisted, and swirl flash nozzle designs. The evaporation efficiency of the atomized droplets...
Journal Articles
Publisher: ASME
Article Type: Research Papers
J. Eng. Gas Turbines Power. August 2011, 133(8): 081201.
Published Online: April 7, 2011
...Jin-Hwa Kim; Martin Kearney-Fischer; Mo Samimy; Sivaram Gogineni Plasma actuators are used to control far-field noise in Mach 1.65 jets from contoured and conical supersonic axisymmetric nozzles (henceforth, contoured and conical jets, respectively). The contoured nozzle is designed using...
Journal Articles
Journal Articles
Publisher: ASME
Article Type: Research Papers
J. Eng. Gas Turbines Power. April 2011, 133(4): 041202.
Published Online: November 19, 2010
...) methodology for geometrically complex internal propulsive flowpaths and large eddy simulation (LES) methodology for the jet structure downstream of the nozzle exit. Temporal data from the LES solution is stored on a flared-cylindrical surface surrounding the jet, to be used for noise propagation...
Journal Articles
Journal Articles
Journal Articles
Journal Articles
Publisher: ASME
Article Type: Research Papers
J. Eng. Gas Turbines Power. March 2011, 133(3): 032804.
Published Online: November 9, 2010
...-delay trends: Ignition delay increased as ambient temperature, ambient pressure, and oxygen concentration decreased. The result of changing injection pressures and nozzle-hole diameters did not significantly affect ignition-delay values for all tested fuels. The variation in ignition-delay values...
Journal Articles
Publisher: ASME
Article Type: Research Papers
J. Eng. Gas Turbines Power. January 2011, 133(1): 012802.
Published Online: September 24, 2010
.... Recent studies have shown that it is possible to measure the three-dimensional geometry of the injector nozzle, and to track changes in that geometry as the needle opens and closes in real time. This has enabled the dynamics of the injector to be compared with the dynamics of the spray, and allows...
Journal Articles
Publisher: ASME
Article Type: Research Papers
J. Eng. Gas Turbines Power. January 2011, 133(1): 011505.
Published Online: September 24, 2010
..., combustion dome, primary dilution jets, secondary dilution jets, and cooling strips to provide convective cooling to the liner. The chamber contracts toward the end to fit the turbine nozzle ring. 2D PIV is employed at an atmospheric pressure drop of 4% (isothermal) to delineate the flow field...
Journal Articles
Publisher: ASME
Article Type: Research Papers
J. Eng. Gas Turbines Power. January 2011, 133(1): 011601.
Published Online: September 13, 2010
... temperature sensor (FTS) developed by General Electric Co. The APFC system determines combustion flame temperatures, validates the values, and integrates an assessment of signal and combustion hardware health to determine how to trim the fuel flow to individual fuel nozzles. Key aspects of the system include...
Journal Articles
Publisher: ASME
Article Type: Research Papers
J. Eng. Gas Turbines Power. November 2010, 132(11): 111504.
Published Online: August 11, 2010
... out for the main and pilot nozzles to avoid flashback and to provide realistic inflow boundary conditions for the combustor. Geometrical details such as air swirlers, vane passages, and liner holes are all taken into account. Tested combustion models show similar downstream distributions of the mean...