A fault tolerant magnetic bearing system was developed and demonstrated on a large flexible-rotor test rig. The bearing system comprises a high speed, fault tolerant digital controller, three high capacity radial magnetic bearings, one thrust bearing, conventional variable reluctance position sensors, and an array of commercial switching amplifiers. Controller fault tolerance is achieved through a very high speed voting mechanism which implements triple modular redundancy with a powered spare CPU, thereby permitting failure of up to three CPU modules without system failure. Amplifier/cabling/coil fault tolerance is achieved by using a separate power amplifier for each bearing coil and permitting amplifier reconfiguration by the controller upon detection of faults. This allows hot replacement of failed amplifiers without any system degradation and without providing any excess amplifier kVA capacity over the nominal system requirement. Implemented on a large (2440 mm in length) flexible rotor, the system shows excellent rejection of faults including the failure of three CPUs as well as failure of two adjacent amplifiers (or cabling) controlling an entire stator quadrant.

Issue Section:
Gas Turbines: Structures and Dynamics
Topics:
Magnetic bearings, Control equipment, Failure, Bearings, Fault tolerance, Rotors, Redundancy (Engineering), Sensors, Stators, System failures, Thrust bearings
1.
Cleaveland
P.
,
1995
, “
Triple Modular Redundant Controllers Meet Safety and Critical Control Needs
,”
I&CS
, Vol.
68
, p.
118
118
.
2.
Fedigan, S. J., Williams, R. D., Shen, F., Ross, R. A., 1996, “Design and Implementation of a Fault Tolerant Magnetic Bearings Controller,” Proceedings, Fifth International Symposium on Magnetic Bearings, pp. 307–312.
3.
Fittro, R. L., Knospe, C. R., and Stephens, L. S., 1996, “Experimental Results of μ-Synthesis Applied to Point Compliance Minimization,” Proceedings, Fifth International Symposium on Magnetic Bearings, pp. 203–208.
4.
Hopkins
A. L.
,
Smith
T. B.
, and
Lala
J. H.
,
1978
, “
FTMP—A Highly Reliable Fault-Tolerant Multiprocessor for Aircraft
,”
Proceedings of the IEEE
, Vol.
66
, No.
10
, pp.
1221
–
1239
.
5.
Humphris
R. R.
,
Kelm
R. D.
,
Lewis
D. W.
, and
Allaire
P. E.
,
1986
, “
Effect of Control Algorithms on Magnetic Journal Bearing Properties
,”
ASME JOURNAL OF ENGINEERING FOR GAS TURBINES AND POWER
, Vol.
108
, No.
4
, pp.
624
–
632
.
6.
Kieckhafer
R. M.
,
Walter
C. J.
,
Finn
A. M.
, and
Thambidural
P. M.
,
1988
, “
The MAFT Architecture for Distributed Fault Tolerance
,”
IEEE Transactions on Computers
, Vol.
37
, No.
4
, pp.
398
–
405
.
7.
Lyons, J. P., Preston, M. A., Gurumoorthy, R., and Szczesny, P. M., 1994, “Design and Control of a Fault-Tolerant Active Magnetic Bearing System for Aircraft Engines,” Proceedings, Fourth International Symposium on Magnetic,
8.
Meeker, D. C., 1996, “Optimal Solutions to the Inverse Problem in Quadratic Magnetic Actuators,” Ph.D. dissertation, University of Virginia, Ann Arbor, MI.
9.
Meeker
D. C.
, and
Maslen
E. H.
,
1995
, “
Fault Tolerance of Magnetic Bearings by Generalized Bias Current Linearization
,”
IEEE Transactions on Magnetics
, Vol.
31
, pp.
2304
–
2314
.
10.
Mizuno, T., Namiki, H., and Araki, K., 1996, “Self-Sensing Operations of Frequency-Feedback Magnetic Bearings,” Proceedings, Fifth International Symposium on Magnetic Bearings, pp. 119–123.
11.
Noh
M. D.
, and
Maslen
E. H.
,
1997
, “
Self Sensing Active Magnetic Bearings Based on Parameter Estimation
,”
IEEE Transactions on Instrumentation and Measurement
, Vol.
46
, No.
1
, pp.
45
–
50
.
This content is only available via PDF.
Copyright © 1999
 by The American Society of Mechanical Engineers
You do not currently have access to this content.