The oxygen reduction activities of platinum and platinum alloy catalysts were evaluated at temperatures up to 150 °C in phosphoric acid solution. The oxygen reduction currents and open circuit potentials were measured using chronoamperometry with double potential steps to eliminate the effects of double layer charging currents and metal deactivationcould be eliminated effectively. Based on the mass activity at 0.7 V versus Ag/AgCl, the commercial PtNi catalyst showed higher performances than commercial Pt catalyst at 150 °C. The commercial PtCo catalyst showed high activities at 90 °C and 120 °C. Intermediate temperature fuel cells based on phosphoric acid doped polybenzimidazole membranes were tested with the alloy cathode catalysts. In the case of Pt–Fe alloy an enhanced performance was achieved in comparison to that with Pt carbon catalysts.
Skip Nav Destination
Article navigation
February 2012
This article was originally published in
Journal of Fuel Cell Science and Technology
Research Papers
Intermediate Temperature Fuel Cell and Oxygen Reduction Studies With Carbon-Supported Platinum Alloy Catalysts in Phosphoric Acid Based Systems
Mohamed Mamlouk,
Mohamed Mamlouk
School of Chemical Engineering and Advanced Materials,
University of Newcastle
, Newcastle upon Tyne, NE1 7RU, UK
e-mail:
Search for other works by this author on:
Jong Hyun Jang,
Jong Hyun Jang
Fuel Cell Research Center,
Korea Institute of Science and Technology (KIST)
, Seoul 136-791, Republic of Korea
Search for other works by this author on:
Keith Scott
Keith Scott
School of Chemical Engineering and Advanced Materials,
University of Newcastle
, Newcastle upon Tyne,NE1 7RU, UK
Search for other works by this author on:
Mohamed Mamlouk
School of Chemical Engineering and Advanced Materials,
University of Newcastle
, Newcastle upon Tyne, NE1 7RU, UK
e-mail:
Jong Hyun Jang
Fuel Cell Research Center,
Korea Institute of Science and Technology (KIST)
, Seoul 136-791, Republic of Korea
Keith Scott
School of Chemical Engineering and Advanced Materials,
University of Newcastle
, Newcastle upon Tyne,NE1 7RU, UK
J. Fuel Cell Sci. Technol. Feb 2012, 9(1): 011002 (9 pages)
Published Online: December 15, 2011
Article history
Received:
August 13, 2009
Revised:
April 12, 2011
Online:
December 15, 2011
Published:
December 15, 2011
Citation
Mamlouk, M., Jang, J. H., and Scott, K. (December 15, 2011). "Intermediate Temperature Fuel Cell and Oxygen Reduction Studies With Carbon-Supported Platinum Alloy Catalysts in Phosphoric Acid Based Systems." ASME. J. Fuel Cell Sci. Technol. February 2012; 9(1): 011002. https://doi.org/10.1115/1.4004461
Download citation file:
Get Email Alerts
Cited By
Special Section on 2D Materials for Electrochemical Energy Storage and Conversion
J. Electrochem. En. Conv. Stor (May 2023)
Modified Silicon Anode for Improved Low-Temperature Performance of Lithium-Ion Batteries
J. Electrochem. En. Conv. Stor (February 2024)
CHROMIUM POISONING MITIGATION STRATEGY IN STRONTIUM DOPED LANTHANUM MANGANITE BASED AIR ELECTRODES IN SOLID OXIDE FUEL CELLS
J. Electrochem. En. Conv. Stor
Effect of Liquid Cooling Structure of Confluence Channel on Thermal Performance of Lithium-Ion Batteries
J. Electrochem. En. Conv. Stor (February 2024)
Related Articles
Aqueous Deposition of Metals on Multiwalled Carbon Nanotubes to be Used as Electrocatalyst for Polymer Exchange Membrane Fuel Cells
J. Fuel Cell Sci. Technol (May,2007)
Design and Testing of a Unitized Regenerative Fuel Cell
J. Fuel Cell Sci. Technol (August,2009)
Optimization of Mesh-Based Anodes for Direct Methanol Fuel Cells
J. Fuel Cell Sci. Technol (June,2010)
Pt 3 Cr ( 111 ) Alloy Effect on the Reversible Potential of OOH(ads) Formation from O 2 ( ads ) relative to Pt(111)
J. Fuel Cell Sci. Technol (May,2005)
Related Proceedings Papers
Related Chapters
Energy Options and Terms: An Introduction
Energy Supply and Pipeline Transportation: Challenges & Opportunities
Clinical issues and experience
Mechanical Blood Trauma in Circulatory-Assist Devices
Members in Bending
Design & Analysis of ASME Boiler and Pressure Vessel Components in the Creep Range