1-11 of 11
Keywords: cantilevers
Close
Sort by
Journal Articles
Journal Articles
Publisher: ASME
Article Type: Research Papers
J. Appl. Mech. January 2012, 79(1): 011005.
Published Online: November 14, 2011
...S. R. Reid; M. Aleyaasin; B. Wang The three-dimensional, dynamic, elastic-plastic response of a right-angle bent cantilever pipe, with an initially uniform, circular cross section, subjected to out-of-plane loading is examined using finite element beam and shell models in ABAQUS. The large...
Journal Articles
Publisher: ASME
Article Type: Research Papers
J. Appl. Mech. November 2011, 78(6): 061013.
Published Online: August 25, 2011
... or simply supported boundary conditions. Nevertheless, many critical components of marine structures where adaptive/morphing capabilities are needed are cantilevered-type structures, including propeller and turbine blades, hydrofoils, and rudders. This paper investigates the 3D transient response...
Journal Articles
Publisher: ASME
Article Type: Research Papers
J. Appl. Mech. July 2011, 78(4): 041011.
Published Online: April 13, 2011
... bending cantilevers elasticity internal friction slip strips elastica friction collapse equilibrium A heavy cantilever that is supported at an internal point may collapse downward into the gap between the fixed end and the internal support (“slip-through” ). Some problems...
Journal Articles
Publisher: ASME
Article Type: Research Papers
J. Appl. Mech. January 2011, 78(1): 011008.
Published Online: October 13, 2010
...M. Chekchaki; V. Lazarus; J. Frelat The mechanical system considered is a bilayer cantilever plate. The substrate and the film are linear elastic. The film is subjected to isotropic uniform prestresses due for instance to volume variation associated with cooling, heating, or drying. This loading...
Journal Articles
Publisher: ASME
Article Type: Technical Briefs
J. Appl. Mech. November 2009, 76(6): 064502.
Published Online: July 21, 2009
... ), pp. 3187 – 3189 . 10.1063/1.1712028 Yi , J. W. , Shih , W. Y. , and Shih , W. H. , 2002 , “ Effect of Length, Width, and Mode on the Mass Detection Sensitivity of Piezoelectric Unimorph Cantilevers ,” J. Appl. Phys. 0021-8979 , 91 ( 3 ), pp. 1680 – 1686 . 10.1063/1.1427403...
Journal Articles
Publisher: ASME
Article Type: Research Papers
J. Appl. Mech. September 2009, 76(5): 051006.
Published Online: June 18, 2009
... eigenpair of a rotating beam, with uniform mass distribution, is identical to that of a corresponding nonrotating uniform beam with the same length and mass distribution. By putting the derived FSF in the finite element analysis of a rotating cantilever beam, the frequencies and mode-shapes of a nonrotating...
Journal Articles
Publisher: ASME
Article Type: Research Papers
J. Appl. Mech. May 2008, 75(3): 031008.
Published Online: April 8, 2008
... deformation in the bonded region. The use of a modified beam theory, which accounts for bending, shear, and extensional deformation in the bonded region, is required in order to model this behavior. Examples are given for cantilever, bridge, and guided structures subjected to either transverse loads...
Journal Articles
Publisher: ASME
Article Type: Research Papers
J. Appl. Mech. January 2008, 75(1): 011007.
Published Online: January 11, 2008
...Jason R. Looker; John E. Sader Knowledge of the flexural vibration frequencies of thin rectangular cantilever plates forms the basis for numerous applications in sensing and instrumentation. Despite the seemingly simple nature of the problem, an accurate formula for the fundamental resonant...
Journal Articles
Journal Articles
Publisher: ASME
Article Type: Technical Papers
J. Appl. Mech. May 2007, 74(3): 461–468.
Published Online: April 9, 2006
... on the model, is presented. The procedure is implemented for the specific case of a rectangular cantilever beam vibrating in its first mode and the resulting equations solved to obtain the damping behavior. The damping characteristics obtained for the rectangular cantilever beam, using the model, is compared...